Yellow or Red wire not connected or incorrect voltage.
Check the connections for proper voltage (11-16VDC).
Black wire not connected – Check connection for ground.
Fuse blown – Replace the fuse with the proper size fuse.
One or more speaker wires may be touching each other or touching chassis ground.
Insulate all bare speakers wires from each other and chassis ground.
Yellow or Red wire touching chassis ground – Check for pinched wire.
Speaker wires touching chassis ground – Check for pinched wire.
Incorrect fuse rating – Replace the fuse with correct rating.
Parking brake safety circuit not connected – Check the connections at the parking brake.
Parking brake not applied – Apply the parking brake.
Reverse circuit not connected – Check the connections at the reverse lamp.
Rear view is set to OFF – Set the rear view to ON.
Dead in remote control – Replace the battery.
Unit is not mounted properly – Check the mounting sleeve and or dash kit.
Physical defect in media – Check the media for scratches.
Focus error or disc is in upside down – Eject the disc or RESET radio.
In some cases aftermarket adapters will be required for installation for retaining factory amplifiers and other factory applications such as steering wheel controls and communications.
Press Audio Transfer to allow audio from the phone to be heard through the speakers.
Auto Answer function is set to ON. Set Auto Answer function to OFF.
The calling mobile device is not set to send the Caller ID, or the service is not available. Some devices may not communicate or work properly with this head unit.
There is no mobile device connected to the head unit.
Pair and/or connect a *compatible mobile device to the head unit according to Bluetooth operation described in the manual.
*Check the Bluetooth Phone Compatibility Chart inside the box
Bluetooth function is not active on the head unit. Activate Bluetooth function in General Setup
Bluetooth function is not active on the mobile device. Refer to owner's manual of your mobile device.
A mobile device is already connected to the head unit. This time the head unit can only be connected to one device at a time. Disconnect current mobile device first, then connect the desired mobile device.
The time limit for the pairing mobile device has been reached. Pair the mobile device within 120 seconds.
The attempted pairing process has failed. Retry the pairing process again.
When the Connect function is set to Manual, the head unit will not connect to any mobile device automatically. Set Connect function to Auto.
Ring tone volume is turned down. Increase the volume of the ring tones using the up and down volume control during the ringing process. MUTE function is activated in the head unit. Press MUTE to cancel the mute function and resume audio.
Possible road noise or interior interference. Close all windows and turn off any fans or A/C.
Microphone opening on the front panel is obstructed. Clear any obstacles in front of the microphone opening.
Physical defect in media – Check media for scratches.
Wrong region – Use discs labels Region 1 or ALL only.
Disc is dirty or scratched – Clean or replace the disc.
File is damaged or bad recording – Recreate the disc with good files.
Message is longer than the LCD can display.
CD format is not compatible with the radio – Rewrite the CD in the correct playback format
The session on the CD/DVD must be closed. Rewrite the CD/DVD with the session closed.
Disc is dirty or scratched – Replace with a nonscratched CD/DVD or clean the CD/DVD disc.
CD-R/RW(+/-) , *DVD-R/RW(+/-) , *DVD+R DL.
(* Media compatible on multimedia units)
Note: All sessions must be closed after recording CD or DVD for proper playback.
Parking brake safety circuit not connected – Check the connections at the parking brake.
Parking brake not applied – Apply the parking brake.
Reverse circuit not connected – Check the connections at the reverse lamp.
Rear view is set to OFF – Set the rear view to ON.
Front panel obstructed – Remove the obstacle and press OPEN again to resume the monitor open/close sequence.
Connections to the navigation system are incorrect.
Check the connections with the navigation system and connect the cables correctly and firmly.
Make sure the antenna is plugged into the SNAV-1 unit.
Make sure the antenna is screwed in properly to the SNAV-1, back it out and try again but don't force it.
Make sure the antenna is plugged into the head unit.
Make sure the antenna is screwed in properly to the head unit, back it out and try again but don't force it.
Refer to the owners’ manual.
SD Card is not loaded with data.
Reload the data and ensure the SD card is in the correct location.
The vehicle has deviated from the route.
Check the route guidance display on the current position screen.
Move back to the route. Search again for a route.
Dead battery in remote control – Replace the battery.
The volume is set to “0” under Guide Speaker setting.
Adjust the volume under Guide Speaker.
Refer to the manual.
You must set the clock of the Navigation feature, refer to the Navigation section of the manual for clock adjustments.
There is no mobile device connected to the head unit.
Pair and/or connect a *compatible mobile device to the head unit according to Bluetooth operation described in the manual.
*Check the Bluetooth Phone Compatibility Chart inside the box
Bluetooth function is not active on the head unit. Activate Bluetooth function in General Setup
Bluetooth function is not active on the mobile device. Refer to owner's manual of your mobile device.
A mobile device is already connected to the head unit. This time the head unit can only be connected to one device at a time. Disconnect current mobile device first, then connect the desired mobile device.
The time limit for the pairing mobile device has been reached. Pair the mobile device within 120 seconds.
The attempted pairing process has failed. Retry the pairing process again
When the Connect function is set to Manual, the head unit will not connect to any mobile device automatically. Set Connect function to Auto.
Ring tone volume is turned down. Increase the volume of the ring tones using the up and down volume control during the ringing process. MUTE function is activated in the head unit. Press MUTE to cancel the mute function and resume audio.
Possible road noise or interior interference. Close all windows and turn off any fans or A/C.
Microphone opening on the front panel is obstructed. Clear any obstacles in front of the microphone opening.
Press Audio Transfer to allow audio from the phone to be heard through the speakers.
Auto Answer function is set to ON. Set Auto Answer function to OFF.
The calling mobile device is not set to send the Caller ID, or the service is not available. Some devices may not communicate or work properly with this head unit.
Physical defect in media – Check media for scratches.
Wrong region – Use discs labels Region 1 or ALL only.
Disc is dirty or scratched – Clean or replace the disc.
File is damaged or bad recording – Recreate the disc with good files.
Message is longer than the LCD can display.
CD format is not compatible with the radio – Rewrite the CD in the correct playback format
The session on the CD/DVD must be closed. Rewrite the CD/DVD with the session closed.
Disc is dirty or scratched – Replace with a nonscratched CD/DVD or clean the CD/DVD disc.
CD-R/RW(+/-) , *DVD-R/RW(+/-) , *DVD+R DL.
(* Media compatible on multimedia units)
Note: All sessions must be closed after recording CD or DVD for proper playback.