FAQ

Where are Extang Covers made?

All Extang covers are made in the USA, manufactured at our Ann Arbor, Michigan facility.

How can I be assured that I am buying a Quality Product?

Extang supports all of our products, 100%, with the industrys strongest warranty: the Maximum Strength Warranty. In addition, a certified ISO9001:2008 facility for quality standards.

Will a Tonneau Cover Improve my gas mileage?

Installing a tonneau cover to your vehicle will help reduce aerodynamic drag and therefore improve MPG. Industry testing has shown gas mileage improvements of up to 10%.

How can I locate the part number of my tonneau?

The part number is typically 10-11 digits, stamped along the underside of the cover, typically located at the driver side cab corner. On hard covers please look for a white sticker to locate the UPC number.

Can I still open my tailgate with an Extang Tonneau on my truck?

Yes, Extang tonneau covers do not restrict the tailgate in any way.

How far above or below the rail does the Tonneau sit?

Most Extang tonneaus sit about an inch above the rail.

How do care for vinyl tonneau cover?

Extang recommends that our vinyl tarps be cleaned with a mild soap, water and a medium bristle brush. If you choose to use a vinyl conditioner, be sure to use our TONNO TONIC. Many other vinyl conditioners contain chemicals that can actually damage your tarp. TONNO TONIC bonds molecular to your Extang Tonno to give it that brand new look day after day. TONNO TONIC will not attract dust nor will it coat or seal your cover. TONNO TONIC allows your tonno to breathe naturally, while enhancing the appearance and providing additional UV protection.

Can I drive through a car wash with an Extang Tonneau Cover installed?

Yes, automatic car washes are safe, however you will not want to select any type of wax treatment as the ingredients within the wax treatment could potentially harm the finish built into the cover.

How do I care for my Signature Series Tonneau?

Extang recommend RaggTop made by Wolfsteins Pro Series to treat the Signature Series material.

How do I care for my Hard Trifold?

Extang recommends that our hard folding covers be cleaned with soap, water and a medium bristle brush. You may use a product like Meguires Quick Detailer to protect and preserve the finish of your tonneau without streaking.

Are your covers waterproof?

There aren't any tonneau covers on the market today that are 100% waterproof. Extang consider covers weather tight and use application specific rubber seals to create superior sealing against water and dust. Tonneaus are built to be weather tight against normal rain and car washing situations.

Are Extang Tonneau Covers difficult to Install?

No, the average installation for a retail customer usually takes 30 to 40 minutes or less (professional installation will take 10-15 minutes). No drilling or tools are required except for an Allen wrench on some applications or a 1/2 inch socket wrench on Encore. Anything you will need to perform the installation is included in the box.

How does your tonno cover attach to my truck?

All Extang Tonno Covers are no damage systems. Most are attached to your truck bed with clamps. There are a very few however, that require what is called a wall plate. This wall plate uses a 3M adhesive tape. The wall plate attaches to the inside of the bed and then the top part of the clamp bolts onto the wall plate. If you have further questions contact Extangs Customer Service Department.
How easy is it to remove the BlackMax Cover?

Both snap covers are designed to roll up quickly against the cab and be secured with strong, convenient straps to allow full access to the bed. Clicklock (Classic) and Leverlock (Blackmax) style corners allow you to attach or remove the tail rail instantly, without any tools. The Monster Bows are spring loaded and can be removed or installed easily with one hand.

I have a truck with a utility track system in the bed. Can I still use the BlackMax Tonneau Cover?

Yes, the installation of a Blackmax or Classic Platinum will not interfere with your track system. The covers allow for full use of the system.

Will the BlackMax work in the Winter as well as in the Summer?

Yes, each cover has an exclusive patented all-climate engineered design to 4-way adjustable for cold weather. The Tuffklamps allow for two bow heights: HIGH for maximum water shedding in harsh weather and for improved gas mileage, and LOW for cold weather tonneau attachment. The MaxSnap slides have two settings: stud low for tight tarp fit in hot weather or stud high for looser tarp fit in cold weather.

Will the BlackMax work with my other truck accessories?

Each cover is designed to work with many aftermarket truck accessories and will fit with all types of bedliners, most bedcaps and 5th wheel hitches.

How do I adjust the tension on my tonneau cover?

To adjust the tension on each cover, you can adjust the bow height to the high setting on the TuffKlamp for a tighter fit or the low setting for a looser fit. The MaxSnap slides can be stud low for a tight tarp fit or stud high for a looser fit.

How far above or below the rail does the BlackMax sit?

These covers are designed to sit 1 inch above the bed height, directly on top of the bed rail.

Can I drive with my Tonneau opened?

Yes, unsnapped and rolled at the cab. The vinyl cover must be rolled up to the cab and secured with the hook and loop.

Do I need to drill my truck when I install my cover?

Absolutely not. No. All of these applications have a 100% no drill, no damage installation.

How long does it take to install my BlackMax Cover?

It takes most customers 30 to 45 minutes to install these covers.

What's the difference between the Classic Platinum and BlackMax?

The Classic Platinum has silver-color rails with silver snaps, which slide freely in the rail, while the Blackmax uses all black components. Additionally, the Blackmax cover snaps around the entire tarp, whereas the Classic Platinum only has snaps on three sides and slides into the cab rail on the 4th side.
How easy is it to take the Encore cover off?

The tonneau can be removed from the bed/rails within minutes.

Will the Encore work with a drop in bed liner that goes over the bed rails?

The bedliner must be an under-the-rail liner, as any over-the-rail liner will interfere with the installation.

Will the Encore work with a drop in bed liner that goes over the bed rails?

The bedliner must be an under-the-rail liner, as any over-the-rail liner will interfere with the installation.

I have a truck with a utility track system in the bed. Can I still use an Encore?

Yes, for a few select make and models.

What are the Encore panels made of?

Extangs exclusively designed panels feature EnduraShield skinned panels paired with a polypropylene core for a superior alternative to the traditional aluminum panel. The EnduraShield skin is constructed from a automotive grade polymer that resists denting, scratches, and UV induced fading.

How much does the Encore weigh?

Depending on the vehicle application it will weigh 50-75 lbs.

Can I stand on my Encore?

Yes, however it is not recommended.

Does the Encore Tonneau Lock?

Yes, as most styles of Encore offer the bolt lock at the cab panel.
How easy is it to take the Express cover off?

It is extremely easy and user friendly. Simply roll the tarp to the cab and secure the cover with the supplied buckles. You can release the cab rail with the release lever located on the passenger side.

Will the Express work with a drop in bedliner that goes over the bed rails?

If the bed liner goes over the side rails, it will need to be trimmed/notched.

How do I adjust the tension on my Express Tonneau cover?

The Express is equipped with an automatic tension system.

Can I drive with my Tonneau opened?

Yes, you can roll the vinyl cover and keep it secure at the cab.

Do I need to drill my truck when I install my Express?

No. The Express is a no drilling/no damage tonneau installation.

How long does it take to install my Express cover?

30-40 minutes, tops.
How easy is it to take the Full Tilt cover off?

The cover can either be unsnapped and rolled to the cab, or the entire cover with side, cab and tail rail can be removed as one piece.

Will the full Tilt work with a drop-in bed liner that goes over the bed rails?

This tonneau will work as long as the bed liner is an under-the-rail bed liner.

I live in a region that gets a lot of snow. Can the Full Tilt hold the snow without bending or stretching?

Yes, however we recommend that you remove the snow from your tonneau just as often as you remove the snow from your windshield.

I live in a region that is very hot. Will the Full Tilt fabric fade in the sun?

No, however it is recommended that you apply Tonno Tonic to the vinyl fabric.

How do I adjust the tension on my Full Tilt tonneau cover?

The sliding rail snaps can be reversed for either the tighter or looser position. Or, you can adjust the bow positions to the higher clamp position (to tighten the tarp) or the bottom clamp position (to loosen the tarp).

How far above or below the rail does the Full Tilt sit?

It sits 1 inch above the rail.

What is the warranty?

10 years on the vinyl cover and lifetime on the frame/components.
How easy is it to take the Trifecta 2.0 cover off?

Extremely easy, simply release the clamps at the tail, fold the cover and loosen the clips at the cab for quick and easy removal.

Will the Trifecta work with a Drop-in Bed Liner that goes over the bed rails?

To perform the installation, simply notch the areas where the clamps will be positioned. The clamps must be flush against the metal of the truck.

I have a truck with a utility track system in the bed. Can I still use a Trifecta 2.0?

Yes. The Trifecta comes equipped with a supplemental clamp kit used to mount inside the track system.

Will the Trifecta work with a 5th Wheel?

Yes, it should work without any issue.

Will the Trifecta work with my other truck accessories?

Some aftermarket truck accessories do affect the tonneau installation.

How much does the Trifecta 2.0 weigh?

The Trifecta tonneau weighs about 35 lbs

Can I drive with my Trifecta Tonneau while open?

The Trifecta tonneau must be fully folded and buckled at the cab. You cannot drive with this tonneau partially open/folded.

How long does it take to install the Trifecta 2.0 cover?

The Trifecta takes longer to remove from the box, than it does to install on your vehicle. This tonneau installs within minutes.
How easy is it to remove the Tuff Tonno cover?

The vinyl cover can be rolled up at the cab and secured with the Velcro straps under the cab rail. You can simply remove the cab rail to fully remove the cover from the bed.

Will the Tuff Tonno work with a drop in bed liner that goes over the bed rails?

Yes. If the liner attaches over the side of the bed, you will need to notch the liner to accommodate the clamps. The clamps must be flush against the metal of the truck.

I live in a region that gets a lot of heavy snow. Will Tuff Tonno hold the snow without bending or stretching?

Yes, however we recommend that you remove the snow from your tonneau just as often as you remove the snow from your windshield.

I live in a region that is very hot. Will the Tuff Tonno fabric fade in the sun?

No, however it is recommended that you apply Tonno Tonic to the vinyl fabric.

I have a truck with a utility track system in the bed. Can I still use a Tuff Tonno?

Yes, the tonneau clamps wall mount under the side rails.

Will the Tuff Tonno work in the winter as well as in the summer?

Yes, the Tuff Tonno comes equipped with a rotating tail rail, which allows for easy tarp installation and removal.

Will the Tuff Tonno work with my other Truck Accessories?

Unfortunately, some aftermarket truck accessories can interfere with the installation of this tonneau.

How far above or below the rail does the Tuff Tonno sit?

The rails sit about 1" above the rails.

Can I drive with my Tuff Tonno opened?

Yes, as long as the vinyl cover is rolled up and secured at the cab.

Do I need to drill my truck when I install my Tuff Tonno?

No, the Tuff Tonno is a no drill/no damage installation. All parts required to perform the installation are included in the box.

How long does it take to install a Tuff Tonno Cover?

Not long, at all. 20-30 minutes max.
How easy is it to take the Solid Fold 2.0 cover off?

The Solid Fold 2.0 offers quick and easy installation and removal. Simply release the clamps at the tail, fold the cover and loosen the clamps at the cab.

Will the Solid Fold 2.0 work with a drop in bed liner that goes over the bed rails?

To perform the installation, notch the areas where the clamps will be positioned. The clamps must be flush against the metal of the truck.

I have a truck with a utility track system in the bed. Can I still use the Solid Fold 2.0?

Yes. The Solid Fold 2.0 comes equipped with a supplemental clamp kit used to mount inside the track system.

What are the Solid Fold 2.0 Panels made of?

The Solid Fold 2.0s exclusive, lightweight, 1-inch thick EnduraShield panel features an automotive grade polymer skin with a polypropylene core to provide the ultimate protection from dent and scratch resistance as well as UV fading.

How much does the Solid Fold 2.0 Weigh?

The Solid Fold 2.0 weighs 50-75 lbs.

Can I stand on my Solid Fold 2.0?

Yes, however it is not recommended.

Does the Solid Fold 2.0 cover lock?

The Solid Fold 2.0 does not offer a locking mechanism, however if you have a locking tailgate your bed is thoroughly secure. Once the tonneau is installed, you must lower the tailgate to access the bed.

Can I drive with my Solid Fold 2.0 open?

Not while unsecure. The Solid Fold 2.0 must be fully folded and buckled at the cab. You cannot drive with this tonneau partially open/folded.

How long does it take to install the Solid Fold 2.0?

The Solid Fold 2.0 takes longer to remove from the box, than it does to install on your vehicle. This tonneau installs within minutes.

UTV Edition

How easy is it to take the cover off?

The Solid Fold 2.0 UTV Edition offers quick and easy installation and removal. Simply release the clamps at the tail, fold the cover and loosen the clamps at the cab.

What are the Solid Fold 2.0 panels made of?

The Solid Fold 2.0s exclusive, lightweight, 1-inch thick EnduraShield panel features an automotive grade polymer skin with a polypropylene core to provide the ultimate protection from dent and scratch resistance as well as UV fading.

How long does it take to install the Solid Fold 2.0 cover?

The Solid Fold 2.0 takes longer to remove from the box, than it does to install on your vehicle. This tonneau installs within minutes.

What is the warranty for the Solid Fold 2.0 UTV?

The Solid Fold 2.0 carries a 90-day warranty from the date of purchase, to the original purchaser/owner.
How easy is it to remove the Revolution Cover?

It is quite easy and user friendly. The Revolution offers a quick removal operation. Once the cover is rolled and secured at the cab, you can remove the cover and cab rail in one step.

For over 30 years, Extang Inc. has been a leading North American manufacturer delivering a wealth of heavy-duty truck bed tonneau covers and accessories. Headquartered in Ann Arbor, Michigan, the company is relentlessly striving to bring products that provide significant benefits and cause no damage to your pickup truck. Every Extang tonneau cover is designed to enhance utility, convenience, and appearance of your vehicle in a matter of few minutes. The covers are capable of withstanding extreme weather conditions, keeping water and dust out of the truck bed. The list of benefits offered by the Extang tonneau covers goes and on, and no wonder why – this brand holds more patents than any other brand in the industry. Perhaps that is why Extang is considered to be Americas number one manufacturer of tonneau covers.

FAQ

UTV Edition