| Weight (lb) | 0.01 lb |
|---|
| Height (in) | 0.7 in |
|---|
| Width (in) | 2.8 in |
|---|
| Length (in) | 2.8 in |
|---|
| Good Maintenance Practices - Section 2 - Bullet 4 | A stain around the weep hole is acceptable. However, if a weep occurs with the engine running and the coolant system pressurized, then the water pump should be replaced. |
|---|
| Product Description | ACDelco GM Original Equipment Engine Water Pump Gaskets are used between the water pump housing and the engine block or another component to seal the interface between the components. The gasket may be made of fiber or a rubberized composite material that provides a liquid-tight connection. The gasket keeps the engine coolant in and keeps air out. These original equipment gaskets have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ⚠ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov |
|---|
| Good Maintenance Practices - Section 3 - Bullet 9 | After installation, pressure-test the system for leaks and check for sufficient fan blade clearance between the blade and radiator shroud. |
|---|
| Good Maintenance Practices - Section 1 - Header | Before purchasing and installing an engine water pump gasket, make sure it is the correct fit for your vehicle. |
|---|
| FAQ - Question 4 | Can a malfunctioning water pump harm my engine? |
|---|
| Good Maintenance Practices - Section 2 - Bullet 1 | Clean all excess dirt and debris from the water pump housing. |
|---|
| Good Maintenance Practices - Section 3 - Bullet 4 | Clean all sealing surfaces, and make sure all old gasket material is removed before installing your replacement component. |
|---|
| Good Maintenance Practices - Section 3 - Bullet 1 | Clean and reinstall the coolant recovery reservoir before flushing the cooling system. |
|---|
| FAQ - Question 3 | Do all water pumps look the same? |
|---|
| Good Maintenance Practices - Section 3 - Bullet 3 | Do not use any non-approved flush agents and replace the coolant according to manufacturer's specifications. |
|---|
| FAQ - Question 5 | Does the water pump affect the temperature inside the passenger compartment of my vehicle? |
|---|
| FAQ - Question 6 | Does the water pump work when my vehicle is turned off? |
|---|
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Engine Overheating - If your vehicle's engine overheats, it may not be receiving the required coolant flow. Make sure that your vehicle's cooling system contains the proper level of coolant. |
|---|
| Good Maintenance Practices - Section 3 - Bullet 2 | Flush the cooling system completely, using power flush equipment or thermal cycling the system with clean water three times. The most effective method of system flushing is to use a coolant exchanger, following the manufacturer's operating instructions. |
|---|
| Features & Benefits - Bullet 2 | GM-recommended replacement part for your GM vehicle's original factory component |
|---|
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspect for leakage at the water pump outlet housing or the rear cover gasket, and leakage at the water pump vent or weep hole. |
|---|
| Good Maintenance Practices - Section 3 - Bullet 10 | Inspect related components in the cooling system, including your fan blades, fan clutch, engine mounts, radiator, belts and hoses, and reservoir. |
|---|
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Leaking Coolant - Puddles of coolant under your vehicle, a constant drip or stream of coolant from the water pump's weep hole, or a constantly empty or low coolant reservoir are all signs of potential water pump wear, and may be caused by cracks in the pump, or seal or gasket failures. |
|---|
| Features & Benefits - Bullet 4 | Manufactured to GM OE specification for fit, form, and function |
|---|
| Features & Benefits - Bullet 1 | May be made from fiber or a rubberized composite material |
|---|
| Good Maintenance Practices - Section 3 - Bullet 5 | Never strike the water pump shaft, since this will damage the new water pump. |
|---|
| Programming Required | No |
|---|
| FAQ - Answer 3 | No. Water pumps can vary greatly in size and appearance depending on the vehicle they are designed for. |
|---|
| FAQ - Answer 6 | No. Your vehicle's water pump keeps coolant moving as long as the engine is running and stops when the engine is turned off. If you want to be able to circulate coolant for a short time after the engine has been turned off, an auxiliary electric water pump is needed. |
|---|
| Features & Benefits - Bullet 3 | Offering the quality, reliability, and durability of GM OE |
|---|
| Signs of Wear & Troubleshooting - Section 1 - Bullet 3 | Rumbling Noise in the Pump - A rumbling, squeaking, or screeching noise near the front of your vehicle when you start it may indicate a malfunctioning water pump bearing. |
|---|
| Good Maintenance Practices - Section 2 - Bullet 2 | Run your vehicle to increase engine temperature, and ensure the system is pressurized. |
|---|
| FAQ - Question 1 | Should the Vehicle Owner’s manual or an expert technician be consulted before making any repairs or adjustments? |
|---|
| Signs of Wear & Troubleshooting - Section 1 - Header | Signs of wear for heater water pumps include but are not limited to: |
|---|
| Good Maintenance Practices - Section 2 - Header | Tips for Water Pump Inspection: |
|---|
| Good Maintenance Practices - Section 3 - Header | Tips for Water Pump Servicing & Installation: |
|---|
| Good Maintenance Practices - Section 3 - Bullet 6 | Torque all bolts according to the manufacturer's specifications and adjust belts to proper tension (if applicable) to manufacturer's specifications. |
|---|
| Good Maintenance Practices - Section 3 - Bullet 7 | Use sealant tabs only if recommended. Some sealant tabs or similar compounds may restrict coolant flow through the passages of some cooling systems. |
|---|
| Signs of Wear & Troubleshooting - Section 1 - Bullet 4 | Visible Component Wear - Worn seals, corrosion, cavitation/pitting of pump components, or a loose or wobbly pump shaft are all signs of wear that may lead to water pump failure and should be addressed. |
|---|
| FAQ - Question 2 | Will ACDelco GM Original Equipment Water Pumps, Kits and other components match the quality of my GM vehicle's original factory parts? |
|---|
| Good Maintenance Practices - Section 3 - Bullet 8 | With the new pump installed, turn the hub by hand and check for rotation. |
|---|
| FAQ - Answer 2 | Yes. ACDelco GM Original Equipment parts are equivalent to your GM vehicle's original factory components. |
|---|
| FAQ - Answer 1 | Yes. Always consult the Vehicle Owner’s manual or an expert technician before making any repairs or adjustments |
|---|
| FAQ - Answer 5 | Yes. As part of regular cooling system operation, the water pump sends hot coolant to the heater core of your engine, which transfers heat into the passenger cabin of your vehicle. If this hot coolant is unable to reach the heater core, then this heat transfer cannot occur, and your passenger compartment remains colder than you want. |
|---|
| FAQ - Answer 4 | Yes. The water pump is responsible for moving coolant through your vehicle's cooling system, keeping the heat generated by your engine at acceptable levels, and helping prevent overheating. A malfunctioning water pump can cause your engine to overheat, which may result in severe and costly engine damage. |
|---|
GM Original Equipment™ Engine Coolant Water Pump Gasket (251-2077) by ACDelco®. Designed utilizing the latest technology, this product by ACDelco features premium quality and will perform better than advertised. Perfect for your vehicle and lifestyle, it is manufactured to meet or exceed stringent industry standards.
ACDelco® - GM Water Pump Installation